Home > Wiper Knowledge > Content

How To Put On Wiper Blades?

Aug 21, 2020

If you don't, you will have vision problems and you may even see scratches on your windshields and even a few broken windshield wipers. 

Windscreen wipers come in several sizes and if you use the wrong one, they will not fit or they will not work properly. Remove the old wiper: Windscreen wipers are available in different sizes but use one of the smaller ones. Carefully lift the arm away from the windscreen and push the small tab into the windscreen wipers where it hits the arms. If you pull down, the wiper blade slips off the side of the windscreen until it is in the right place on the blade. 


When the rubber blade is turned away from the arm, the wiper arm can be guided through the windscreen. When you remove the wiper mounting from the rear window, slide out the old wiper blade and turn it so that it is vertical. Turn it around the mounting brackets and pass it through a small tab on the side of your windscreen wiper. 

Carefully push the wiper arm back into the windscreen so that it touches the glass. Make sure nothing sticks and, if necessary, wipe a rag around the edge to clean everything. Once you have installed the new blade in your wiper arm, try it out. 

If the blade slips, switch off the windscreen wiper and let the unit sit tighter and switch on again. Check the windscreen wipers by switching them on and off and using the water from the windscreen washer to lubricate the glass surface. Instructions for adding windshield washer fluid to your Honda Accord can be found at this link. 

It is good to replace the windscreen wipers on your Honda Accord or other cars with an older version of the same model year. 

It is not necessary to remove the wiper arm to replace the rear wiper blades for each type of vehicle. If the rear wiper blades of the vehicle are not used correctly, they lose their effectiveness over time. You can replace them by lifting the wiper arms away from the window, turning the old wipers outwards to "pull them out," and then turning the new blades in until they snap into place. 

Normally you can get a spare wiper blade in a car parts shop, but you should be sure that you need a new wiper blade if it leaves a streak or makes a squeak. You can test this by spraying windscreen detergent and watching the wipers and arms clean. 

There are cheaper parts, and some may even be cheaper, but it is best to replace and save the bloated labor costs. 

Find out what type of wiper change you need and how to remove your wipers below. Check the size of the required wiper blades and learn more about the type of blade and the size you need. As with any mechanical blade, the left and right blades may not be of the same length. 

If the windscreen is no longer free after cleaning the blades and using the wipers, replace it as soon as possible, but not before the windscreen is free again.

When the ignition switch is on, set the windscreen wiper lever to off position by setting it to ON. The new wipers are inserted by clicking into the wiper arm and then reconnected to the wiper. 

Finally, lift the wiper lever out of the fog position you once lifted and release and lift the old wipers by pressing the right side of the wiper blade and then the left side. Attach the new blades by inserting the wiper arm into the opening in the middle of each blade. Pull the knives up until you hear them click, then push them down again. 

Lower your arm to the windscreen and repeat the process with the other arm, then back up again, and so on until all the blades are in place. 

I hope this guide will help you the next time you need to replace your car's windscreen wipers. You can also replace the refills by showing you how to change the wiper blades in this article. 

The frequency of wiper blades varies depending on the type of blade in your car, although wiper blades generally outlast conventional blades. The blades can also become weak, lose their tension against the glass, bend, and bend. If you have a problem with the chatter, you can replace the entire blade as long as it does not make contact with the windscreen. 

 A general decrease in visibility on the road is another sign that the wiper blades need to be replaced. The best way to monitor the intervals for wiper blade replacement is to have them checked every time you change the oil. 

The wiper blades use a rubber squeegee to wipe water, snow, and ice out of sight. The metal wiper arms that hold the wipers are spring-loaded - so charged that they push against the windscreen during a storm.